Cleaning furniture, waxing it, and reviving a tired finish
Dust, then test, then clean only what needs cleaning, then wax or do not. The order matters more than the products, and most of the products sold for this job are the ones the sources warn about.
- Start here: the essentials
- 1. Where this guidance comes from, and who it was written for
- 2. Dusting comes first
- 3. What is actually on the surface
- 4. Only as needed
- 5. Two thin coats or none
- 6. What the sources say not to use
- 7. Reviving a tired finish, and where this manual stops
- 8. The rags
- 9. See it: Dana's chest, cleaned
- 10. Practice: one surface, properly
- 11. Your piece
- 12. Check your work
- 13. Knowledge check and scenario
Start here Essentials
At minimum this chapter asks you to dust one surface properly, test it with mineral spirits, clean only what needs cleaning, and then wax it or write down why not. The named products, the silicone problem and the source disagreements are Go deeper on a first pass.
- Dust it properly before you put anything wet on it. And check the finish is sound enough to dust (section 2).
- Test with mineral spirits and see whether wax comes off. This is also the stop test (section 3).
- Clean only what needs cleaning, one small area at a time. Not on a schedule (section 4).
- Let it dry, then wax it thinly, or decide not to. Two thin coats rather than one thick one (section 5).
- Deal with the rags before you put the kettle on. Flat, on concrete, outdoors (section 8).
Minimum time: about an hour for one surface, plus several hours of drying. Done when: the surface is clean and dry, you have waxed it or written down why not, and the rags are flat on concrete outdoors.
1. Where this guidance comes from, and who it was written for Understand
Almost everything in this chapter comes from two publishers: the National Park Service's Conserve O Gram leaflets, written for park staff looking after collection objects in historic structures, and the American Institute for Conservation's guidance for owners of old furniture. That provenance is worth stating up front for three reasons.
It is why the guidance is cautious. These are instructions for people handling objects that have no replacement, written by conservators who see what goes wrong. A kitchen table is not a collection object, and you are entitled to decide that some of this is more care than your piece needs.
It is why some of the figures do not transfer. When the waxing leaflet says most objects need rewaxing every one to four years, it says that about a furnished historic structure, and about ten-year intervals for objects in exhibit cases. Those are settings, not universal intervals, and this manual gives the figures with their settings attached rather than converting them into advice for a dining room.
And it is why the stops are real. The same leaflets tell trained park staff to stop and consult a conservator at several specific points. This manual carries those stops as they are written rather than converting them into confidence, because a stop aimed at a trained member of staff applies at least as much to a reader at home.
Four results in this chapter end your part of the job, and all four come from the published guidance rather than from this manual's caution.
- The finish softens under mineral spirits. The cleaning leaflet says not to attempt to clean the piece, and to consult a furniture conservator.
- The surface is painted. It says painted surfaces should not be cleaned beyond dusting unless you are trained in distinguishing paint types, and to consult a conservator about any treatment beyond dusting.
- The finish is wax over bare wood. It says that beyond dusting, no attempt should be made to clean such furniture, because the methods it describes will damage that kind of finish.
- The surface is unfinished wood. It says not to use water, because of the risk of raising the grain, and that cleaning heavily soiled bare wood with mineral spirits should be done only by trained staff or under a conservator's direction.
In each case what follows is Who to hire for furniture work rather than a gentler version of the same action.
One more thing to settle before any of it: you need to know which finish you have. Almost every branch in this chapter depends on the answer, which is why Finding out what finish is on your furniture is the chapter to read first and is marked as such at the foot of this page.
2. Dusting comes first
Dusting is the one routine action in this manual, and it is worth more than any product you could buy.
The reasoning is in the Park Service's dusting leaflet. It notes that hard, sharp particles such as those of siliceous origin tend to cause abrasion while organic particles are more likely to cause chemical damage, and that dust attracts water vapor from the air, creating a microclimate of higher relative humidity next to the object. Its leaflet on upholstered furniture adds that dust acts as an attractant and a food source for insects. So dust is a slow abrasive, a local humidity problem and an insect attractant at once.
Check before you touch
Before dusting a finished surface, that leaflet says to check the condition of the finish, and that finishes which are unstable, meaning flaking, cracking or with lifting edges, and wood surfaces that have splintered or have loose or lifting veneer, should not be dusted. In those cases it says to request a conservator's advice, and also where you suspect the finish is original. The survey in Surfaces, veneer and hardware is what tells you this.
How the sources say to do it
Here the two publishers differ in emphasis, which is worth knowing rather than hiding.
One agency's method The Park Service's leaflet says vacuuming is, under most circumstances, the most effective and least damaging way to remove dust from stable finished wooden surfaces, and that it is the preferred method for unfinished wood, because those surfaces tend to snag fabric and wiping with a cloth can imbed soils in the pores. For delicate surfaces it describes holding a vacuum nozzle just above the surface and sweeping dust toward it with a soft artist's brush no wider than the nozzle, with the suction reduced as far as is practical.
The American Institute for Conservation's leaflet, written for owners, says dry dusting with a soft cloth is recommended for routine cleaning once a protective coat of wax has been applied, that a soft cotton cloth or artist's brush is best, and that a clean cloth slightly dampened in water may help with more stubborn dirt. Both agree that feather dusters are not recommended: the AIC leaflet says the feathers tend to get caught in cracks and crevices and can cause detachment of fragile veneers and gilding.
The practical default this manual takes from the two: vacuum with a brush attachment where you have one and the surface is stable, cloth where you do not. If you use a cloth, the dusting leaflet's own advice is to turn it frequently so a clean surface meets the object each time, to keep several clean cloths on hand, and to wipe in the direction of the grain where possible. It adds that a dampened cloth can reduce snagging on a stable finish, that if there is any question whether the finish is water-soluble you should test with a dampened cotton swab in a hidden area first, and that a moistened cloth should not be used on unfinished wood, because the soils can migrate into it.
For upholstery, the leaflet on upholstered furniture says that if the show fabric is stable it can be vacuumed regularly at low suction, preferably through a nylon mesh window screen of about 18 by 18 inches with protective tape at the edges, using a water-filtering or HEPA vacuum. And if the fabric is unstable, not to attempt to vacuum, and to consult a conservator.
3. What is actually on the surface
Dusting removes loose soil. What is left is often not the finish but an accumulation on top of it: wax, polish, grease and decades of handling. Before cleaning you need to know which you are looking at, and the test is the same one the finish chapter uses.
The cleaning leaflet's instruction: apply mineral spirits with a cotton swab to a small, inconspicuous area to test the solubility of the finish. It names V.M. & P. naphtha from paint and hardware stores, or Stoddard solvent from chemical supply houses, as examples. And then the stop: if the mineral spirits softens the finish, do not attempt to clean the piece, and consult a furniture conservator.
If the finish does not soften, you have learned two useful things at once: that mineral spirits is a safe cleaning agent for this surface, and whether there is wax on it. Wax shows as a dulling where you wiped and a waxy smear on the swab.
Convention On wax, one point from the finishing writer whose solvent sequence this manual uses: wax cannot be neutralized, which some product labels claim, and has to be washed off with a petroleum-distillate solvent. Mineral spirits is one. So removing a wax layer is not a separate exotic operation; it is the cleaning step below, continued until nothing more lifts.
4. Only as needed
The first rule in the cleaning leaflet is about when, not how: cleaning should be performed only as needed, not on a routine schedule, and should be attempted only on surfaces that have a sound, stable, clear finish, or on those that are completely unfinished. It says cleaning beyond dusting is not always desirable, and that some furniture has developed a surface patina, an accumulation of finish, wax and soil, that may be considered an integral part of the piece's appearance, with wear and soil patterns indicating historic use. Where that question arises, it says to consult a conservator.
So the first decision is whether to clean, and "it looks dull" is not by itself a reason. The leaflet's own trigger is that after dusting or buffing the finish looks dull or heavily soiled, or there is a build-up of wax.
The procedure, as published
- Remove loose soil first, with a clean soft cotton cloth or a vacuum with a clean soft brush attachment.
- Test with mineral spirits on a swab, in a small inconspicuous area, and stop if the finish softens.
- Wipe the surface with a cotton cloth dampened with mineral spirits. A soft bristle brush dipped in mineral spirits helps around carvings and intricate decoration.
- Wipe with a clean cloth and let it dry for several hours. Several hours, not several minutes.
- If stubborn dirt remains, wipe lightly with a clean cotton cloth dampened in a weak solution of a mild soap and warm water, wrung out well. The leaflet names Ivory Flakes, shavings from Ivory bar soap, or Orvus paste or liquid, and specifically excludes Ivory dishwashing liquid.
- Follow with a thorough wiping with a cloth dampened slightly in clear water, then dry completely with another clean cotton cloth.
- Rewax when the wood has dried completely, because these methods remove the protective wax coating.
The leaflet's wording is unambiguous: never use detergents, because they leave a film that is difficult to remove and which may permanently damage some finishes. That rules out dish soap in the ordinary modern sense, household surface sprays and most things sold as cleaners. The named mild soaps are soaps rather than detergents, which is the distinction being drawn.
Where water needs extra care
The same leaflet says water should be used very sparingly when cleaning veneered or inlaid furniture: clean one small area at a time, then wipe dry with a clean cloth before moving to the next. If the finish is worn or cracked, it says to use mineral spirits rather than water. And it repeats the warning about snagging the raised edges sometimes found on veneered and inlaid surfaces.
For shellac specifically, which is what a positive alcohol test in the finish chapter means, this manual's practical advice is to stay with the mineral spirits route and leave the soap-and-water step for a different piece. Shellac is softened by water and by alcohol, and the soap step introduces water to a film that does not want it.
5. Two thin coats or none
Waxing is optional. It is also the one surface treatment in this manual that both publishers recommend, within limits.
The AIC leaflet says the best maintenance for clear-varnished furniture is a coating of good paste wax, describing wax as a very stable material that does not change chemically over time and provides protection from moisture and airborne pollutants. Its dosage: a thin coat applied following the directions on the can, no more than once a year. Its exclusions: it may not be appropriate to wax furniture that is gilded, painted or lacquered, or furniture with unstable veneers or a flaking finish, and it says to consult a conservator if any question about appropriateness arises.
The Park Service's waxing leaflet gives the method in more detail.
| Question | What the leaflet says |
|---|---|
| What kind of wax | Paste wax only. It excludes liquid and aerosol polishes because most contain silicones, which could be harmful to finishes |
| On what surfaces | Stable clear finishes such as shellac, lacquer and varnish |
| On what surfaces not | Unfinished bare wood: wax penetrates the pores and is nearly impossible to remove |
| Test first | When waxing a finish for the first time, test the wax in an inconspicuous area to see whether the solvent in the wax softens the finish |
| Which solvents | Prefer the weaker organic solvents, turpentine and mineral spirits. Avoid waxes with xylene and toluene, which can damage some finishes and are more of a health hazard |
| How much | Sparingly. Too much makes a sticky surface that attracts dust and dirt |
| How to apply | A clean cotton cloth, rubbing first in a circular motion and then along the grain |
| How long before buffing | 30 to 60 minutes, then buff with a clean cotton cloth |
| How many coats | Two thin coats are preferable to a single thick one; repeat if the luster is uneven or more protection is wanted |
| Clean first | The leaflet says to clean the finish before applying a new film of wax |
| How often | In a furnished historic structure, most objects need rewaxing every one to four years. Objects in exhibit cases may need it only at ten-year intervals |
| When not to bother | As a rule, rewaxing is not necessary as long as the existing wax layer can be buffed to a sheen. Objects that are used or touched may need it more often |
| Carved and irregular surfaces | Apply with a small soft brush such as a toothbrush; after drying, buff with a soft fiber brush such as a shoe brush, with foam padding taped to the brush's wooden ends |
| Upholstered edges | Lay sheets of polyester film or similar over the upholstered edge so wax is not wiped onto the fabric |
Physical principle Note the rewaxing figures and their settings. One to four years is for a furnished historic structure; about ten years is for an exhibit case. Neither is a figure for a kitchen table, and the leaflet's own more general rule is better guidance for a house: if the existing wax still buffs to a sheen, it does not need redoing, and a piece that gets used and touched will need it more often than one that does not.
Two things wax does that surprise people
Clouding. The leaflet says wax applied in an environment with excessive heat or relative humidity can cloud or whiten, and that it can be removed with mineral spirits, then rewaxed once the environmental problems have been corrected. So a cloudy wax layer is a reason to look at the room, which is Keeping furniture from getting worse.
Whitish specks. Light-colored waxes can leave whitish specks in wood pores and in carving recesses on darker finishes, and the leaflet notes these may not appear until the solvent has fully evaporated, which could be several weeks. It gives two answers: pick them out with a wood pick, or use a pigmented wax over darker finished woods such as walnut and mahogany, keeping natural or light-colored wax for lighter woods such as maple and pine.
6. What the sources say not to use
This is the section that contradicts most of what is sold for this job, and it rests on two sources rather than on taste.
Furniture does not need feeding
The AIC leaflet is direct about it: it was once thought that furniture needed to be "fed" with various mixtures of oils and other materials to keep it from drying out, and a better approach would be to keep furniture in a stable environment. From there it rules out two product categories by what they do.
Drying oils. Furniture oils are not recommended for maintenance, it says, because many contain linseed oil or other drying oils, and when used repeatedly these create a gummy, insoluble surface coating that darkens and obscures the grain of the wood.
Non-drying oils. Other polishes contain non-drying oils such as lemon oil, which it says attract and entrap dirt and grime.
The State Historical Society of Iowa's collections guidance for wooden objects reaches the same place in three words, listing "avoiding furniture polish" among its basic care points.
Silicone
Silicone polishes are not recommended, the AIC leaflet says, because they leave a film that is difficult to remove and can interfere with future finish treatments. The Park Service devotes a whole leaflet to it, and that leaflet is the reason this manual keeps mentioning it.
It says the majority of commercial furniture polishes contain silicone in one form or another, and that it is found in almost all liquid and aerosol wax preparations, added to make application easier and to obtain a higher gloss. Once applied it can be difficult to remove. If a new finish is later applied over a surface that has had it, small crater-like indentations called fish eyes appear. And the detail that explains why it matters so much: a silicone residue can be present even when the old finish has been stripped down to bare wood, and the contamination does not become apparent until a new finish is applied.
Its instruction for a collection is to record the fact on the object's record if a wax or polish containing silicone is known or suspected, which is why the What was done sheet in your condition report has a materials column, and why "silicone suspected" is a legitimate entry.
Product-specific That leaflet was written in 1993 and says these products had then been on the market for about 35 to 40 years. Read it as what it is: a 1993 statement about the market of its day. What has not changed is the mechanism, and the practical instruction, which is that a cheap aerosol used this afternoon can make a refinishing job harder for somebody in thirty years.
| Product | What the source says it does | Who says so |
|---|---|---|
| Furniture oils containing linseed or other drying oils | Repeated use creates a gummy, insoluble coating that darkens and obscures the grain | American Institute for Conservation |
| Polishes containing non-drying oils such as lemon oil | Attract and entrap dirt and grime | American Institute for Conservation |
| Silicone polishes, and most liquid and aerosol preparations | Leave a film that is difficult to remove and interferes with future finish treatment; cause fish eyes; residue survives stripping to bare wood | American Institute for Conservation; National Park Service |
| Detergents | Leave a film that is difficult to remove and may permanently damage some finishes | National Park Service |
| Waxes carrying xylene or toluene | Can damage some finishes, and are more of a health hazard | National Park Service |
| Feather dusters | Feathers catch in cracks and crevices and can detach fragile veneers and gilding | American Institute for Conservation |
| Paste wax on bare wood | Penetrates the pores and is nearly impossible to remove | National Park Service |
7. Reviving a tired finish, and where this manual stops
"Reviving" is where the most popular advice in this subject lives, and where the least of it has a source.
What this manual offers, because a source states it: cleaning, which often changes a surface more than people expect; waxing, which raises the sheen and makes a surface more level; and removing a wax bloom with mineral spirits. That is the list.
There is a real technique, used by professionals, for reviving a deteriorated shellac finish by working its own solvent back into it so that the existing film flows and re-forms rather than being replaced. It has a literature and practitioners who do it well.
This manual does not describe it, because the research behind this manual found no source for it that met the standard everything else here is held to. Rather than give you a half-remembered version of an irreversible operation on the only original finish your piece has, the honest thing is to name it as work a professional does and stop. If your report says you have a tired shellac film and you want more than cleaning and wax, that is a conversation with a furniture conservator, and Who to hire for furniture work is how to start it.
The same applies to the published methods for removing rings, heat marks and crazing. Several circulate, they contradict each other, which one applies depends on the finish, and this manual has no sourced basis for choosing between them. Surfaces, veneer and hardware names those faults and leaves them named.
What you should expect from cleaning and waxing alone, stated plainly so you can judge whether it is worth your afternoon: a surface that is noticeably cleaner, more even in sheen, and darker and richer where dirt had been sitting in the grain; and the same scratches, the same rings, the same crazing and the same worn-through patches as before. The accumulated grime often turns out to have been most of what looked wrong. The faults in the finish stay.
8. The rags
Rags used with oil finishes can catch fire on their own, without a spark or a flame, as the oil cures and generates heat faster than a crumpled pile sheds it.
The National Park Service's fire prevention bulletin on spontaneous combustion names oil-soaked rags among the materials involved, cites an NFPA estimate of 14,070 fires a year, and recounts an incident of its own in which rags used with linseed oil on tool handles ignited. Its instruction is to spread soiled rags in a single layer on concrete, out of direct sunlight, with the corners secured so they cannot blow into a pile, and to let them go hard before disposal. For businesses it names an OSHA-approved container.
If a pile is already smoking: call 911, and do not disturb it. Spreading a smoking pile out introduces oxygen.
This applies to rags used with oil finishes. Solvent-soaked rags are a different hazard, a flammable vapor rather than a self-heating one, and they go outdoors too, away from flames and pilot lights, until the solvent has evaporated. The same box appears in What can hurt you in old furniture.
Plan this before you start rather than at the end. The moment you need somewhere to put a rag is the moment it is most tempting to drop it in a bin, and that is the decision this box exists to pre-empt. Choose the spot, outdoors, before you open anything.
Where the two publishers differ, and what to make of it
On dusting, the Park Service's leaflet prefers a vacuum with a brush for stable finished surfaces and says wiping with a cloth can imbed soils in the pores, especially on unfinished wood. The AIC leaflet, written for owners, recommends dry dusting with a soft cotton cloth or an artist's brush once wax has been applied, and allows a cloth slightly dampened in water for stubborn dirt.
These are not contradictory so much as written for different situations. The Park Service is addressing staff with HEPA vacuums and micro-attachments working on collection objects; the AIC is addressing an owner with a cloth. They agree on the substance: remove dust regularly, work gently, avoid feather dusters, be careful around loose veneer and mounts, and leave an unstable surface undusted.
This manual's default, which is its own and not either source's: vacuum with a soft brush attachment where you have one, and use a well-turned clean cloth where you do not, wiping with the grain, on a surface you have checked is stable.
The named waxes, and the disclaimer that goes with them
The Park Service's waxing leaflet names specific silicone-free paste waxes: Staples, Butchers, Johnson, Goddard's Cabinet Makers Wax, Trewax, Antiquax and Behlen Blue Label. It also names Renaissance Wax and microcrystalline wax as highly water-resistant but difficult to buff evenly on large surfaces, suggesting they suit small wooden objects, including items combining wood and metal. It notes that most of these contain carnauba, beeswax and synthetic waxes with a carrier such as paraffin and solvents such as mineral spirits and turpentine, and that each is reversible because all can be removed with mineral spirits.
That list comes with the series' own disclaimer, which this manual reproduces because reprinting a government product list without it would misrepresent what it is: "Mention of a product, a manufacturer, or a supplier by name in this publication does not constitute an endorsement of that product or supplier by the National Park Service. Sources named are not all inclusive. It is suggested that readers also seek alternative product and vendor information in order to assess the full range of available supplies and equipment."
Two further cautions of this manual's own. That leaflet was revised in 1993, so product formulations may have changed since, and a product's name on a 1993 list is not evidence about what is in the tin today. And availability varies. What transfers reliably is the specification rather than the brand: a paste wax, carried in a weaker solvent such as mineral spirits or turpentine rather than xylene or toluene, with no silicone.
Why silicone matters years later
The mechanism is worth understanding because it is the clearest example in this manual of a cheap action with a long tail. Silicone fluid has very low surface tension and spreads into a surface and into the wood beneath it. When a new finish is later applied, it will not wet the contaminated spots evenly, and pulls back from them into small craters, the fish eyes the leaflet names. Because the residue can remain after stripping to bare wood, the problem is not solved by removing the old finish, and dealing with it takes specialized equipment and experience, which is why that leaflet routes it to a furniture conservator.
The practical consequence for you today is small and worth doing: if you suspect a piece has had aerosol polish on it, write "silicone suspected" on the materials line of your What was done sheet. That is a two-second entry which may save somebody a mystifying afternoon in twenty years.
What a professional can do to a tired shellac finish
Without describing a procedure this manual has no source for: the general shape is that shellac remains soluble in its own solvent for as long as it exists, which is the same property the solvent test exploits, and that property allows an existing film to be worked rather than replaced. What makes it professional work is judgment about whether a particular film will take it, control of how much solvent goes in, and the ability to stop. The failure mode is removing the finish you were trying to save.
If this is what your piece needs, the useful questions from Who to hire for furniture work are the ones about what will be removed and what will be added, and whether the proposed treatment keeps the existing film or replaces it. Those two questions will tell you quickly which kind of job is being proposed.
9. See it: Dana's chest, cleaned See it
Dana's walnut chest. Shellac finish, one white ring in the finish on the top, general dullness, dust in the carved edge of the top drawer.
What Dana did, in order. Checked the survey from the surfaces chapter for lifting veneer or flaking finish, and found none on the top. Vacuumed with a soft brush attachment on low suction, sweeping toward the nozzle with an artist's brush around the carving. Tested with mineral spirits on a swab on the inside of the top rail: no softening, a faint waxy smear and gray soil on the swab.
The cleaning. Wiped the top with a cotton cloth dampened in mineral spirits, a section at a time, turning the cloth as it loaded. A soft bristle brush dipped in mineral spirits for the carved edge. Wiped with a clean cloth. Left it four hours.
What Dana skipped, and why. The mild soap and water step. The finish is shellac, which water softens, and the mineral spirits pass had already lifted most of what was there. The leaflet offers the soap step for stubborn dirt that remains, and on this surface none did.
The waxing. Tested the wax on the same hidden spot to see whether its solvent softened the finish. It did not. Two thin coats of a silicone-free paste wax, circular then along the grain, 45 minutes to dry, buffed with a clean cotton cloth. A toothbrush for the carving, buffed afterwards with a shoe brush.
The result, honestly. The top is noticeably darker and richer, the dullness is gone, and the grain reads properly for the first time since Dana inherited it. The white ring is exactly as it was.
Known: the finish is shellac, it did not soften under mineral spirits, and there was a wax layer and soil on the surface.
Assumed: that the whole top carries the same finish as the rail Dana tested. One test spot is one test spot.
Still open: the ring. Under the assumption that the finish is original shellac, this manual's published treatments do not reach it, and Dana's plan sheet records it as "deciding later," with a conservator's opinion as the thing that would settle it.
The rags. Flat on the concrete path, single layer, out of the sun, with a brick on two corners. Hard by the next morning.
What went on the report: date; "vacuumed, cleaned with mineral spirits on a cloth, no soap step (shellac); two thin coats paste wax, silicone-free, brand recorded; ring untouched."
The sources behind this chapter:
- Cleaning wood furniture (National Park Service, Conserve O Gram 7/1, July 1993): the whole cleaning procedure in section 4, the four stops in the Limits box, the mild soaps and the detergent warning.
- Waxing furniture and wooden objects (National Park Service, Conserve O Gram 7/2, revised July 1993): the waxing table in section 5, the clouding and whitish specks, the carving method, and the named waxes under Go deeper.
- Dusting wood objects (National Park Service, Conserve O Gram 7/5, September 2002): why dust damages, the check before dusting, and the vacuum method.
- Silicone in furniture waxes and polishes (National Park Service, Conserve O Gram 7/6, July 1993): the silicone problem, fish eyes, and the instruction to record it.
- Caring for Your Treasures (American Institute for Conservation): the furniture leaflet, for paste wax as the best maintenance for clear-varnished furniture, the dosage and exclusions, feather dusters, and the passage on feeding wood and the oils.
- Collections care: wooden objects and furniture (State Historical Society of Iowa): a short tips list that includes avoiding furniture polish.
- Spontaneous combustion: fact or fiction? (National Park Service): the rag instruction in section 8.
10. Practice: one surface, properly Practice
Minimum: one surface, dusted, tested, cleaned if it needed it, waxed or not, with the decision written down. Time: about an hour of work spread over a day, because of the drying. Materials: a vacuum with a soft brush attachment if you have one, several clean cotton cloths, cotton swabs, mineral spirits, a soft bristle brush, a silicone-free paste wax, a toothbrush and a shoe brush if the piece is carved, ventilation, and somewhere outdoors for the rags.
- Check the surface is stable enough to touch. No flaking, cracking or lifting edges, no loose veneer. If there are, stop and read Surfaces, veneer and hardware again.
- Choose where the rags will go before you open anything.
- Dust thoroughly, vacuum with a brush if you can, cloth turned frequently and wiped with the grain if not.
- Test with mineral spirits on a swab in a hidden place. Stop entirely if the finish softens.
- Decide whether cleaning is needed. If the surface looks right after dusting, write that down and skip to the wax question.
- Clean with mineral spirits on a cloth, a small area at a time, turning the cloth. Let it dry for several hours.
- Test the wax on the hidden spot, then apply two thin coats, circular then with the grain, 30 to 60 minutes between application and buffing.
- Write it on the What was done sheet: date, what you used, what you skipped and why.
- Deal with the rags before anything else.
The half-and-half test. On a large surface, clean half of it and leave the other half, with a clean line down the middle, and look at it in raking light before you go any further. Two things come out of this. You see exactly what the cleaning achieved, which is often more than expected and is the honest measure of whether the rest of the piece is worth the afternoon. And you see what it did not touch, which is the list of faults cleaning was not going to address, and which you can then take to What not to do to old furniture, and why with evidence rather than with a hope.
11. Your piece Your piece
12. Check your work Check your work
Criteria
- Did you identify the finish before putting anything on the surface?
- Did you check the surface was stable before dusting it?
- Did you test with mineral spirits in a hidden place, and stop if it softened?
- Did you decide whether cleaning was needed, rather than cleaning by default?
- If you waxed, was it paste wax, tested first, applied in two thin coats and buffed after 30 to 60 minutes?
- Is what you used recorded on the What was done sheet, including anything suspected rather than known?
- Are the rags flat on concrete outdoors?
Worked example
Dana's session identified the finish first, checked stability, tested and got a clean result, cleaned with mineral spirits only, skipped the soap step with a written reason that follows from the finish, tested the wax before using it, applied two thin coats, and recorded both the materials and what was deliberately left alone. Checked against the criteria it passes on all seven. The most useful line on the record is the one about the ring being untouched, because in two years that is what stops somebody assuming it was tried and failed.
Common mistakes
- Cleaning before identifying the finish. Most of this chapter branches on the answer.
- Dusting a flaking or lifting surface. The dusting leaflet says not to, and to ask a conservator.
- Cleaning on a schedule. The guidance says only as needed, and some accumulation is part of the piece's appearance.
- Reaching for dish soap. Detergents are specifically excluded; the named soaps are soaps.
- Water on shellac, veneer or bare wood. Each has its own reason in the guidance, and none of them is fussiness.
- Too much wax. It makes a sticky surface that attracts dust, which is the opposite of what you wanted.
- Buffing immediately. The leaflet gives 30 to 60 minutes.
- Using an aerosol polish "just this once." Silicone residue survives stripping to bare wood and shows up when somebody refinishes decades later.
- Leaving the rags until the end. Decide where they go before you open anything.
What is still unresolved
This chapter cleans and waxes. It does not remove rings, heat marks or crazing, and it does not revive a deteriorated shellac film, because the manual has no source it trusts for any of those. What it leaves you with is a surface in its best honest condition and a clear view of which faults remain, which is the right input to What not to do to old furniture, and why. Where the piece lives, and what that does to it across a year, is Keeping furniture from getting worse.