What your piece of furniture is actually made of
Solid wood, veneer over a core, or manufactured board: the answer is different for different parts of the same piece, and it decides more about what can be done than age or style does.
- Start here: the essentials
- 1. Why the material decides more than the style
- 2. Where the evidence is
- 3. Three things it could be
- 4. Secondary woods
- 5. Naming the wood, and where that stops
- 6. See it: two pieces read
- 7. Practice: the four-line reading
- 8. Your piece
- 9. Check your work
- 10. Knowledge check and scenario
Start here Essentials
At minimum this chapter asks you to look at one piece from underneath and decide, for three or four parts of it, whether each is solid wood, veneer over something, or manufactured board. The species work and the composite-board detail are Go deeper on a first pass.
- Turn the piece over, or open it, and look at what nobody finished. Undersides, drawer interiors, the back boards, the inside faces of rails (section 2).
- Find an exposed edge and decide solid, veneer or board. An edge tells you in seconds what a polished face rarely shows (section 3).
- Pull a drawer out and look at its sides, its bottom and the back of the case. These are the secondary woods, and they are usually more honest than the front (section 4).
- Write four lines into the What it is sheet. Build, primary wood, secondary wood, and what you are not sure of (your condition report).
Minimum time: about 25 minutes. Done when: your What it is sheet says solid, veneer or board for the top, the sides and the drawer fronts, and names a secondary wood or says you could not name one.
1. Why the material decides more than the style Understand
People usually try to date a piece before they try to read it. That is the wrong way round, because almost every decision in this manual turns on what the thing is made of rather than on when it was made. Whether a scratch can be touched depends on whether there is a twenty-thousandth of an inch of walnut under the finish or three quarters of an inch of it. Whether a loose joint can be taken apart depends on whether the joint is in solid wood or in particleboard with a cam fitting. Whether a water ring is a cosmetic problem or a structural one depends on what is under the veneer.
Physical principle The reason is that these materials move differently, fail differently and take repair differently. Solid wood swells and shrinks across the grain with the moisture in the air and will keep doing so for as long as it exists, which is why Keeping furniture from getting worse has a calculator in it. Veneer is a thin sheet glued to something else, so it is held still by its substrate and comes under stress when the two disagree. Manufactured board moves little until it gets wet, at which point it swells, and the swelling tends not to reverse the way solid wood's does.
The American Institute for Conservation opens its own furniture guidance by saying that furniture is an assemblage of materials, naming metal, bone, plastic, shell, leather and fabric alongside paints and natural and synthetic resins, and that all of them have to be taken into account. That is a useful corrective to thinking of a chest of drawers as "wood." A single ordinary chest can hold four species of wood, a shellac finish, steel screws, brass pulls, a plywood back and a paper label.
So this chapter asks a narrow question, part by part rather than piece by piece: what is this part made of, and what does that rule out? Some parts will not classify. A part you cannot classify is a legitimate entry on the sheet, as long as it says so rather than being left blank.
Three words this manual uses throughout. Solid means the part is one piece of wood, or several boards of wood joined edge to edge, through its whole thickness. Veneer is a thin sheet of wood glued over a different material, called the substrate or the core. Manufactured board covers plywood, particleboard, fiberboard and medium-density fiberboard, all of which are made by gluing wood in pieces, chips or fibers into a sheet. Every one of these is defined again in the glossary.
2. Where the evidence is
Furniture tells the truth where nobody expected it to be looked at. A maker who was going to finish the top beautifully had no reason to finish the underside of it, and a maker in 1890 had no more reason than one in 1990. So the first move in this chapter is the one people skip, which is to put the piece on its back or its side, or pull its drawers out, and look at the parts that were not meant to be seen.
Before you tip anything, read the short warning in the next box. It is the one instruction in this chapter that can cost you a leg.
AIC's furniture guidance says to examine a piece for loose or damaged joinery before moving it, and to lift rather than drag, because lateral pressure on legs and feet can shear them off. It says to remove shelves, doors and drawers first, to lift a table by the apron or legs rather than the top, and to lift a chair by the seat rails rather than the arms or crest rail. If the piece racks when you push it, read Joints, racking and breaks before you turn it over.
Once it is safe to handle, these are the places worth your attention, roughly in order of how much they give you:
| Where | What it shows | Usually tells you |
|---|---|---|
| Drawer sides and backs | Unfinished wood, joint type, tool marks | Secondary wood, how the drawer was made, whether drawers match each other |
| Drawer bottoms | Solid board or panel, grain direction, any chamfer | Solid versus board construction, and sometimes a pencil mark or a label |
| The back of a case | Boards, plywood or hardboard; how it is fixed | Era of construction and whether the back has been replaced |
| The underside of a top | Raw wood, saw marks, fasteners, the join between boards | Solid or veneered, how the top is attached, any repairs |
| The inside face of a rail or apron | Unfinished surface, joint ends, glue blocks | Species, joinery, previous repairs |
| Any broken or chipped edge | A free cross-section | Solid, veneer or board, immediately and with no doubt |
Take a flashlight. Most of this is in shadow, and a raking beam across an unfinished surface shows tool marks and grain that a ceiling light flattens out. Take photographs as you go; Writing a condition report wants them, and a photograph of a drawer side is worth more than a sentence about one.
A last place worth checking, because it costs nothing: labels, stamps, paper tags and chalk or pencil writing. These turn up inside drawers, on the back of a case, under a seat rail and on the underside of a tabletop. A maker's label settles more about a piece in two seconds than everything else in this chapter, and it belongs in your notes even when you cannot read it.
3. Three things it could be
With an edge in front of you, the classification is quick. You are looking at the cut end or the exposed side of the material, and each of the three looks different.
Solid wood
On an edge, solid wood shows grain that continues from the face around onto the edge and keeps going. The figure on the face and the figure on the edge are part of the same thing. On a wide top you will often see the glue lines where several boards were joined edge to edge, which is normal construction and not a fault. End grain, where you can see it, shows pores and growth rings.
The giveaway that something is solid rather than veneered is continuity. If you follow a distinctive mark, a knot, a streak of darker wood, a ray, and it carries on around the corner onto the edge or the end, the part is solid.
Veneer over a core
Veneer shows as a seam. Look at the edge of a tabletop or a drawer front and you will see a line, often very fine, where the thin facing sheet stops and something else begins. Underneath will be solid wood, plywood or particleboard, and the facing will usually also be stopped at the edge with a narrow strip of matching wood called edge banding, which has its own seam.
Two other signs. First, figure that looks too good to be true. Convention A highly figured, book-matched pattern, mirrored about the center line of a drawer front, is usually veneer, because that effect is produced by slicing one log into sheets and laying consecutive sheets side by side. Second, lifting or blistering, which only happens to something glued to something else.
Convention Veneer is not a sign of cheapness, and reading it that way will lead you wrong. Veneering is centuries older than the furniture most people own, and a great deal of highly regarded furniture is veneered, because veneering is how figured and scarce woods were made to go round. What veneer changes is not the piece's standing but what you can safely do to the surface.
Manufactured board
Plywood shows alternating layers on an edge, in cross-grain pairs, usually with a thin facing. Particleboard shows chips and flakes, visibly separate, bound in resin; it crumbles rather than splinters. Medium-density fiberboard, usually called MDF, shows a dense uniform brown material with no visible grain, which breaks with a smooth, almost chalky face. Hardboard, the thin dark brown sheet often used for the back of a case, is a fiber product with one smooth side and one textured side.
| Look for | Solid | Veneer over a core | Manufactured board |
|---|---|---|---|
| Grain at the edge | Continues from the face | Stops at a seam | None, or layers in cross-grain pairs |
| Weight for the size | Varies by species | Varies by core | Usually heavy, particleboard notably so |
| What a chip reveals | More of the same wood | A different material under a thin facing | Chips, fibers or plies |
| When it gets wet | Swells, may cup or split, usually recovers in shape | Glue may release; the facing lifts or bubbles | Swells permanently; particleboard and MDF do not recover |
| What repair looks like | Often possible in matching wood | Specialist work once the facing is lost | Replacement rather than repair |
This classification does not tell you a piece's quality, age or worth, and the manual does not value anything. A solid pine chest from 1972 and a veneered mahogany chest from 1810 are both legitimate answers to "what is it made of" and the material says nothing about which one matters more. What it settles is narrower: what each part will do when it gets wet, how it will move across a year, and which faults can be addressed without specialist work.
4. Secondary woods
The primary wood is what the piece shows: the top, the drawer fronts, the visible faces. The secondary wood is what it is built from behind that: drawer sides, drawer bottoms, drawer backs, back boards, glue blocks, the hidden parts of frames and the dust boards between drawers.
Secondary woods are worth looking at for three reasons. They are unfinished, so you see the wood itself rather than a stained and coated version of it. They were chosen for cost and availability rather than for show, so they tend to be local. And they are the parts most likely to be original, because nobody refinishes a drawer side.
What to record is simple: what the secondary wood looks like, whether it is the same throughout the piece, and whether it differs from the primary wood. A piece whose drawer sides are all one wood and whose drawer fronts are another is ordinary. A piece where one drawer's sides are a different wood from the other three is telling you something, and what it is usually telling you is that the drawer was replaced or rebuilt. That is a finding, and it goes on the report.
Within a single drawer, look at how the sides meet the front. Dovetails, a joint of interlocking wedge-shaped pins and tails, are the common joint in older drawers, and their shape and regularity are among the clues How old your furniture is reads. Here, all you need is whether the joint type is the same on every drawer.
5. Naming the wood, and where that stops
Sooner or later you will want to say "it is walnut" rather than "it is a medium brown hardwood." This is the part of the chapter where the honest answer is less satisfying than people expect.
What you can do by eye is narrow. Color, grain pattern, pore size and arrangement, weight, ray figure where it shows and the part of the piece it sits in will usually get you to a short list. A wide-pored, strongly rayed, pale to medium brown hardwood with prominent flecks on a quartered surface is very likely an oak. A fine-pored, warm reddish-brown wood that darkens with light exposure is a reasonable cherry candidate. Those are useful narrowings and they are worth writing down.
Test it What you cannot do by eye is name the species with confidence, and it is worth knowing why rather than just being told. Real wood identification is microscopic anatomy. InsideWood, the reference database at NC State University Libraries, holds over ten thousand descriptions and tens of thousands of images, and it is searched by coded anatomical features taken from the International Association of Wood Anatomists feature list, from thin sections under a microscope. A guess from a photograph is not the same activity.
You can narrow a wood to a short list from appearance and from where it sits in the piece. You cannot reliably name a species by eye, and a confident species name written on a report is worse than "a medium brown hardwood, possibly walnut," because the next person will believe it. In practice only two decisions in this manual actually need a species: the seasonal movement arithmetic in Humidity and movement, which needs a shrinkage figure, and a repair made in matching wood, which is a professional's job anyway. For everything else, the short list is enough. Where you do want certainty, the identification is done from a sample under a microscope rather than from a photograph, and the next section says who will do that for you.
So write what you can defend. "Oak, probably white oak on the ray figure" is a good entry. "Oak" is acceptable. "English brown oak, around 1840" is a story.
If you want the wood identified properly
There is a route, and it is free. The USDA Forest Products Laboratory runs a Wood Identification Public Service through its Center for Wood Anatomy Research in Madison, Wisconsin. Its own terms, as published on that page when it was read for this manual: the service is free for private US citizens, it takes up to three samples per year per household, results usually come within four weeks, and samples are not returned and may be destroyed in the process. A sample should be about 1 by 3 by 6 inches, and a piece too small may limit what can be identified.
Three limits on that page matter more than the convenience does, and they are the reason this manual keeps telling you to hedge. Ask the authority The laboratory identifies wood "typically to genus," meaning oak or maple rather than a particular oak. It says it does not determine the age or origin of a sample. And the service is for private citizens rather than businesses, and not for legal disputes. So the most authoritative identification available to an ordinary owner in the United States still returns a genus, which is a good reason not to write a species on a report from across a room.
The practical catch for furniture is obvious once stated: a sample that size has to come from somewhere. On most pieces worth identifying there is nowhere to take it from, which is why the narrowing above is what you will actually use. Where there is a loose, already-detached piece, or a scrap from a part that is being replaced anyway, the service is a real option.
What the cores do when they get wet
Each core material fails in its own way, which is why the distinction is worth making before any water goes near a piece. Plywood resists swelling better than the other boards because its cross-laminated plies restrain each other, but the glue lines can delaminate, and the thin face veneer lifts first. Particleboard swells at the edges and at any unsealed cut, and the swelling is permanent: the chips absorb water, expand and do not return, which is why a particleboard carcass that has stood in a damp basement has soft, biscuit-like corners that crumble under a fingernail. MDF behaves similarly, swelling and losing its surface, and once a screw hole in MDF has swollen it will not hold that screw again.
The practical consequence runs through the rest of the manual. A water event on solid wood is an event to manage, and the NPS emergency guidance for water-soaked furniture is largely about not drying it too fast, because rapid drying and the stresses it sets up cause splitting and deformation. A water event on particleboard is often simply the end of that part.
Bentwood and laminated parts
Some chair parts are neither solid in the ordinary sense nor veneered: they are laminated, built up from thin layers glued together in a curve, or steam-bent from solid stock. A laminated curve shows its layers on an edge, like plywood but all running the same way. These parts fail at their glue lines rather than across the grain, and a delaminating curved chair part is not a joint repair; it is a job for someone with the right clamping setup.
What a formaldehyde label on a newer piece tells you
If your piece was made recently and has composite parts, it may carry a label about formaldehyde emissions. EPA regulates formaldehyde emissions from hardwood plywood, medium-density fiberboard and particleboard under Title VI of the Toxic Substances Control Act, and the rule covers household and other finished goods containing those products, which includes finished furniture. The dates matter if you are reading a label: by June 1, 2018 panels and finished products had to be certified compliant with TSCA Title VI or with California's CARB ATCM Phase II by a third-party certifier; until March 22, 2019 CARB Phase II products could be labeled to either standard; after that date composite wood products must be labeled as TSCA Title VI compliant. EPA issued a further final rule in October 2026 updating the standards, concerning voluntary consensus standards and the quality-control test method. The numerical emission limits are not on EPA's summary page; they are in the regulation itself at 40 CFR Part 770.
What this is useful for: a TSCA Title VI label on a piece is a floor on its date, not a ceiling, and it tells you that at least part of the piece is composite wood rather than solid.
6. See it: two pieces read See it
Dana's walnut chest. Inherited from a grandparent's house; nobody knows where it came from. Four drawers.
Known, because Dana looked: the top is solid, because a dark streak in the grain runs over the front edge and continues on the underside. The drawer fronts are veneered: there is a fine seam at the top edge of each one, and the figure on the second drawer is mirrored about its center line. The drawer sides are an unfinished pale wood, straight-grained, and they are the same on three drawers. Three drawers have hand-cut dovetails with a visible scribe line across the tails; the fourth has machine-cut dovetails of even spacing, and its sides are a slightly different color.
Assumed, and it is Dana's assumption: that the primary wood is walnut, from color, pore pattern and weight. Nobody has looked at a thin section under a microscope and nobody is going to.
Still open: whether the fourth drawer is a replacement or an original drawer rebuilt later. The sides and the joint both differ from its neighbors, so something happened to it, but which of the two it was is not settled by anything Dana can see. A furniture conservator or an experienced dealer who can handle the piece settles that; Who to hire for furniture work says which.
What goes on the report: top solid, drawer fronts veneer over an unidentified core, sides and back unfinished pale secondary wood, primary wood probably walnut, fourth drawer differs from the other three in both joint and secondary wood.
Priya's teak sideboard. Bought from an online listing, described as mid-century. Sliding doors, an oiled finish gone gray and dry, veneer lifting at one front corner.
Known: the lifting corner gives a free cross-section, and under the facing is a pale, uniform, fine-grained core, not plies. The case sides are faced the same way. The door frames are solid: grain runs around the edges.
Assumed: that the wood is teak, on color, the oiled look and the era of the design. Test it This is the kind of assumption the section above says is not settled by eye. Priya's report should say "probably teak."
Still open: whether the lifting veneer has lost its substrate underneath or is simply released from it, which pressing gently along the edge with a fingertip begins to answer and a professional finishes.
Why it matters here: if the assumption of teak is wrong, the seasonal movement figure in Humidity and movement changes, and so does the answer to why the doors stick in August. Under the assumption that it is teak, the calculator's figure is a reasonable estimate; if it is another species the estimate moves with it.
Two references worth opening while you are at this:
- InsideWood (NC State University Libraries): the wood anatomy database. Worth two minutes just to see what a real identification is built from, which is the fastest cure for overconfidence about naming a species from a photograph.
- Wood Identification Public Service (USDA Forest Products Laboratory): the free federal identification service, its sample requirements, and its own statement that it identifies to genus rather than species.
- Moisture relations and physical properties of wood (USDA Forest Products Laboratory, Wood Handbook chapter 4): the federal reference this manual's movement calculator is built on. Its shrinkage tables are the reason a species name is worth having.
- Formaldehyde emission standards for composite wood products (US EPA): what the label on a newer composite piece refers to, and the dates each labeling requirement took effect.
7. Practice: the four-line reading Practice
Minimum: one piece, three parts, four lines written down. Time: about 25 minutes. Materials: a flashlight, a phone camera, a soft blanket or towel to set the piece down on, and your condition report open.
- Clear a space and lay something soft down. You are going to tip a piece of furniture, and the floor is the thing most likely to damage it in the next half hour.
- Check for loose joinery, then tip or open the piece. If it racks, stop and read Joints, racking and breaks first.
- Photograph four things: an exposed edge, a drawer side, the back, and any label or writing. Put something in frame for scale, a ruler or a coin.
- Classify three parts out loud before you write anything: "top is solid, drawer fronts are veneered over something, back is plywood." Saying it first makes the uncertain ones obvious.
- Write the four lines into the What it is sheet: build per part, primary wood, secondary wood, and one line for what you could not settle.
The narrowing exercise. Take the secondary wood you found and try to narrow it rather than name it. Write down: pore size, whether pores are in rings or scattered, color, weight relative to the primary wood, and whether it shows ray flecks. Then write a short list of two or three candidates and the one fact that would separate them. The useful outcome is not the name; it is noticing how few features you can actually see and how far that gets you, which is the point the boundary above is making.
8. Your piece Your piece
9. Check your work Check your work
Criteria
- Does your sheet give a build for each of at least three parts, rather than one answer for the whole piece?
- Where you wrote a species, can you say what the evidence was, and would you still write it if someone asked you to defend it?
- Does the sheet distinguish what you observed from what you concluded? "A seam at the edge" is an observation; "veneered" is a conclusion from it, and both are worth having.
- Is there at least one line saying what you could not settle, with who or what would settle it?
Worked example
Dana's report says: top solid; drawer fronts veneer, core not identified; sides and back unfinished pale secondary wood; primary wood probably walnut, from color and pore pattern; fourth drawer's sides and joints differ from the other three, cause not settled. Checked against the criteria, that passes on all four: it is part by part, the species is hedged with its evidence, the observations are separable from the conclusions, and the open question names who settles it.
Common mistakes
- Classifying the piece instead of the parts. Most furniture is mixed. A chest can have a solid top, veneered fronts, solid sides and a hardboard back, and writing "veneered" over all of it loses the three facts that matter.
- Reading veneer as a verdict on quality. It is a construction method, not a grade.
- Writing a species as fact. The cure is to write the evidence beside it, which forces the hedge automatically.
- Tipping the piece before checking its joints. This is the one mistake in the chapter that breaks something.
- Leaving a cell blank instead of writing "not sure." In two years a blank reads as forgotten, and an honest "not sure" still reads as information.
What is still unresolved
This chapter cannot date the piece, which How old your furniture is takes up, and it cannot tell you what is on the surface, which Finding out what finish is on your furniture settles with three solvents. It cannot name a species to certainty, and nothing short of microscopy can. And it does not say what any of it is worth, which this manual does not do; Who to hire for furniture work says who does.